|
Composite C-Hub Suspension Option Set, Complete F+R
#300900
Composite C-hub suspension set, complete for front and rear. Modeled after the XRAY's superb aluminum C-hub suspension (#300901), the components of this set are molded from a tough composite material for lighter weight, without sacrificing quality or rigidity.
|
|
|
Alu C-Hub Suspension Option Set, Rear
#300931
This superb new optional C-hub suspension gives a slightly softer ride, and is a great way to set up your T1 for different racing conditions.
|
|
|
C-hub Complete Tuning Set
#302100
Complete tuning set of all composite C-hub suspension parts is a great addition for serious racers to exactly tune the car to any track condition.
|
|
|
Alu Roll Center Bridge
#303030
Simple - smart - stunning - stylish.
A great, stylish-looking option part CNC machined from high-quality duraluminum will not only add executive look of your T1 but will also enable you to adjust the roll center very easily with 2 different roll center mounting positions. Mount this bridge between both rear bulkheads and insert the adjustable ball of the camber link into the inner position to change the roll center.
|
|
|
Roll Center Alu Holder - Set (2)
#303031
This set is used to relocate the inner mounting points for the rear camber links. Used with #303093 rear shocktower to utilize shorter camber links with short arm suspension, and also allows changes to rear roll center. Set includes alu pivot ball posts and mounting hardware.
|
|
|
Suspension Arm Rear Lower EVO2
#303111
Molded rear lower suspension arm. May be used on either left or right sides. Additional shock mounting positions.
|
|
|
Alu Rear Lower Arm
#303115
CNC-machined high-quality aluminum rear lower arm with 3 different shock mounting positions. The arm is hard coated for a long life. These arms will make the rear of the car more stiff, increasing steering slightly. It is advised to use these rear alu arms for high-grip tracks.
|
|
|
Adj. Rear Turnbuckle L/R 25mm (2+4)
#303200
Adjustable turnbuckle set for adjusting camber of rear uprights. Includes four molded ball joints and two turnbuckles manufactured from world-renowned top-secret "Hudy Spring Steel".
|
|
|
Adjustable 5.8mm Ball End - Spring Steel (2)
#303230
Ball end manufactured from world-renowned top-secret "Hudy Spring Steel" to which rear upper camber links attach. Can be adjusted into and out of rear bulkheads to compensate for wheelbase changes. Set of two.
|
|
|
Upright Rear
#303310
Molded rear upright. Can be used for both left and right side.
|
|
|
Alu Upright Rear For C-Hub Suspension
#303355
CNC-machined rear upright for C-hub suspension is made from highest-quality duraluminum. Can be used on either left or right side. Includes two nylon bushings for ball-bearings.
|
|
|
Alu Upright Rear 1° Outboard Toe-In (L+R)
#303356
CNC-machined rear upright made from highest-quality duraluminum features an integrated 1° outboard toe-in. Use the outboard toe-in will increase the corner speed. Complete set of left and right blocks. Includes composite bushings for ball-bearings.
|
|
|
Alu Upright Rear 2° Outboard Toe-In (L+R)
#303357
CNC-machined rear upright made from highest-quality duraluminum features an integrated 2° outboard toe-in. Use the outboard toe-in will increase the corner speed. Complete set of left and right blocks. Includes composite bushings for ball-bearings.
|
|
|
Anti-Roll Bar Rear 2mm (Set)
#303400
If your car is understeering, then try this optional rear anti-roll bar. The rear anti-roll bar will decrease rear chassis roll and decrease rear traction. This will give your car more steering.
|
|
|
Anti-Roll Bar Rear 2mm
#303420
Rear anti-roll bar (2.0mm thick) is included in the optional Rear Anti-Roll Bar Set, part number 302400. This is the STIFFEST rear anti-roll bar.
|
|
|
Anti-roll Bar Rear 1mm
#303421
Optional rear anti-roll bar (1.0mm thick) has 2 ground surfaces. This provides stiffness adjustment possibilities of the rear anti-roll bar. This is the SOFTEST rear anti-roll bar.
|
|
|
Anti-roll Bar Rear 1.5mm
#303422
Optional rear anti-roll bar (1.5mm thick) has 1 ground surface. This provides stiffness adjustment of the rear anti-roll bar. This is the MEDIUM rear anti-roll bar.
|
|
|
Short Nylon Ball Joint 4.9mm (4+2)
#303450
Molded short 5mm ball joints, for connection to 5mm ball ends. Set of four ball joints and connectors. Used for the rear anti-roll bar mounting.
|
|
|
Drive Shaft Replacement Plastic Cap 3mm (4) - V2
#305240
Low friction drive pin clips for protection and cushioning of drive shaft pin in diff outdrives. Set of four.
V2 Update: Both the material and design have been improved to reduce wear of the differential outdrives.
|
|
|
Wheel Axle-22mm-Integr. Hex Hub - (Factory Kit) (2)
#305311
CNC-machined hardcoated duraluminum rear wheel axles with hex hubs. Ultra-true, direct, wobble-free wheel mounting ensures âśslop-free" wheel rotation. Wheel axles have been strategically lightened to reduce rotating mass without compromising strength.
|
|
|
Wheel Axle â“ 22mm - Offset âś-1mmâť - Hard Coated (2)
#305312
CNC-machined hardcoated duraluminum rear wheel axles with hex hubs. Ultra-true, direct, wobble-free wheel mounting ensures âśslop-free" wheel rotation. Wheel axles have been strategically lightened to reduce rotating mass without compromising strength.
The wheel axles feature a -1mm offset which means that they are 1mm shorter than standard wheel axles.
|
|
|
Wheel Axle â“ 22mm - Offset âś+1mmâť - Hard Coated (2)
#305313
CNC-machined hardcoated duraluminum rear wheel axles with hex hubs. Ultra-true, direct, wobble-free wheel mounting ensures âśslop-free" wheel rotation. Wheel axles have been strategically lightened to reduce rotating mass without compromising strength.
The wheel axles feature a +1mm offset which means that they are 1mm longer than standard wheel axles.
|
|
|
Wheel Axle - 22 mm - Integr. Hex Hub - Spring Steel (2)
#305315
Optional wheel axles manufactured for XRAY by HUDY from the world-famous top-secret "Hudy Spring Steel(TM)". These are a direct replacement for the original duraluminum wheelaxles, and will be virtually impossible to damage or wear out. The wheelaxles are strategically CNC-machined so they are as light as possible to reduce rotating mass, while maintaining ultimate strength.
|
|
|
Drive Shaft - 51 mm - Spring Steel (2)
#305320
Rear drive shafts, CNC-machined from world-renowned top-secret "Hudy Spring Steel". These race quality drive shafts are the smallest in the world, exclusively manufactured by HUDY. Set of two.
|
|
|
Drive Shaft-51mm-Spring Steel - (Factory Kit) (2)
#305321
Rear drive shafts, CNC-machined from world-renowned top-secret "Hudy Spring Steel". These race quality drive shafts are the smallest in the world, exclusively manufactured by HUDY. Drive shaft diff end has been strategically lightened to reduce rotating mass without compromising strength.
|
|
|
Pivot Ball 6.8mm - Spring Steel (2)
#307350
Rear lower 6.8mm pivot balls, manufactured from "Hudy Spring Steel". Hardened and ultra-precisely hand ground for low weight, very high durability and long life. Set of two.
|
|
|
HQ Ball-Bearing 10x15x4 Blue Covered (2)
#309052
Ultra High-Performance, High-Quality Ball-bearings
Top-quality professional ball-bearings for a super free and super smooth drive train. These highest quality ball-bearings are fitted with special polyamid blue covers and plastic ball cage for maximum smoothness, long life, highest tolerance and maximum performance. These ball-bearings have more balls inside the cage than the regular ball-bearings, making them much more resilient under loads. The blue polyamide covers are easy to remove for quick and comfortable servicing. A "must have" item!
|
|
|
HQ Ball-Bearing 10x15x4 Blue Covered (12)
#309053
High-performance high-quality ball-bearing
Top-quality professional ball-bearings for super free and super smooth drive train. These are the most quality ball-bearings with special polyamid blue covers and plastic cage for balls for maximum smooth operation, long life, highest tolerance and maximum performance. These ball-bearings have more balls inside the cage than the regular ones, that makes the ball-bearings higher performance. The covers are easy removable for quick and comfortable servicing. A must have item!
A complete set of 12 ball-bearings will substitute all 10x15x4 ball-bearings on your T1.
|
|
|
High-Speed Ball-Bearing 10x15x4 Blue Covered (2)
#309054
New high-speed ball-bearings manufactured specially for XRAY. Top-quality professional ball-bearings for a super-free, super-smooth drivetrain. These highest quality ball-bearings are fitted with special polyamid blue covers, and are degreased and lightly oiled with AeroShell Fluid 12 oil for maximum smoothness, long life, highest tolerance and maximum performance.
|
|
|
Ball-Bearing 10x15x4 Rubber Sealed - Oil (12)
#309055
New high-speed ball-bearings manufactured specially for XRAY. Top-quality professional ball-bearings for a super-free, super-smooth drivetrain. These highest quality ball-bearings are fitted with special polyamid blue covers, and are degreased and lightly oiled with AeroShell Fluid 12 oil for maximum smoothness, long life, highest tolerance and maximum performance.
|
|
|
Universal Set Of Plastic Shims
#309319
Set of shims for setting static wheelbase. Fits over rear lower pivot pins, servo saver, front one-way diff and other shims.
|
|
|
Pin 2x10 (10)
#981210
Polished chrome pin. Dia. x length = 2mm x 10mm. Set of 10 pieces.
|
|
ID |
Product Name |
Released |
303356 |
|
May 09, 2005 |
303357 |
|
May 09, 2005 |
305312 |
|
May 09, 2005 |
305313 |
|
May 09, 2005 |
303160 |
|
Mar. 16, 2005 |
901304 |
|
Jul. 30, 2004 |
901308 |
|
Jul. 30, 2004 |
901408 |
|
Jul. 30, 2004 |
902306 |
|
Jul. 30, 2004 |
931015 |
|
Jul. 30, 2004 |
941015 |
|
Jul. 30, 2004 |
967100 |
|
Jul. 30, 2004 |
981210 |
|
Jul. 30, 2004 |
303031 |
|
Jul. 23, 2004 |
305311 |
|
Mar. 26, 2004 |
305321 |
|
Mar. 26, 2004 |
303159 |
|
Feb. 12, 2004 |
302100 |
|
Jun. 18, 2003 |
303153 |
|
May 15, 2003 |
303151 |
|
Mar. 24, 2003 |
| |
|
|